У меня почти новый WD Green, но срок гарантии уже истек. Он лежал на полке.
Я хотел бы проверить это перед использованием.
Первый шаг, который я сделал - это запуск полного тестирования с использованием Data Lifeguard Tools. Этот тест дает мне ошибку
0226 Sector Relocation Error
Официальная рекомендация - заменить диск. Однако очевидно, что поставщик заинтересован в том, чтобы продавать больше жестких дисков.
Состояние SMART говорит о том, что повторное отображение равно нулю, поэтому я понятия не имею, в чем здесь может быть ошибка. Интересно, есть ли способ переназначить проблемные сектора?
Обновление: SMART
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD10EARS-00Y5B1
Serial Number: WD-WCAV********
LU WWN Device Id: 5 0014ee 259379483
Firmware Version: 80.00A80
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Nov 22 12:52:42 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (20100) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 231) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3031) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 167 122 021 Pre-fail Always - 4633
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 30
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 23
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 13
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 8
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 21
194 Temperature_Celsius 0x0022 117 103 000 Old_age Always - 30
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 14 inconsistent with error log pointer 5
ATA Error Count: 14 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 40 00 04:30:32.893 SET FEATURES [Set transfer mode]
ef 03 46 00 00 00 40 00 04:30:32.892 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 40 00 04:30:32.890 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:27:11.365 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:27:11.362 IDENTIFY DEVICE
Error 13 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 40 00 04:30:32.892 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 40 00 04:30:32.890 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:27:11.365 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:27:11.362 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:26:15.054 SEEK [OBS-7]
Error 12 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
70 00 00 00 00 00 40 00 04:27:11.365 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:27:11.362 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:26:15.054 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:26:15.052 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:24:33.301 SEEK [OBS-7]
Error 11 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
70 00 00 00 00 00 40 00 04:26:15.054 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:26:15.052 IDENTIFY DEVICE
70 00 00 00 00 00 40 00 04:24:33.301 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:24:33.298 IDENTIFY DEVICE
Error 10 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
70 00 00 00 00 00 40 00 04:24:33.301 SEEK [OBS-7]
ec 00 00 00 00 00 40 00 04:24:33.298 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 22 -
# 2 Conveyance offline Completed without error 00% 18 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.