Итак, пару дней назад мой 3-летний ноутбук с win7 работал (программы не реагировали и т.д.), Поэтому я решил запустить chkdsk, однако это оказалось плохой идеей, так как он завис в одном файле на этапе 4/5 в течение примерно 24 часов я получал BSOD с ошибкой bad_system_config_info, и всякий раз, когда я сейчас загружаю Windows, через пару минут она перестает отвечать на запросы, и мне приходится принудительно выключать ее. Я загрузил портативную версию Ubuntu, запустил gsmartcontrol и получил следующие результаты для жесткого диска:
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: S2WFPRB7
LU WWN Device Id: 5 000c50 04b0cae93
Firmware Version: 0005HPM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Aug 19 19:42:26 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 070 064 006 Pre-fail Always - 81234683
3 Spin_Up_Time 0x0002 099 098 000 Old_age Always - 0
4 Start_Stop_Count 0x0033 098 098 000 Pre-fail Always - 2202
5 Reallocated_Sector_Ct 0x0033 091 091 036 Pre-fail Always - 201
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 290912486
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10198
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0033 098 098 020 Pre-fail Always - 2115
183 Runtime_Bad_Block 0x0032 100 253 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 34578
188 Command_Timeout 0x0032 100 001 000 Old_age Always - 4295042219
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 046 045 Old_age Always - 34 (Min/Max 25/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 68
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 61
193 Load_Cycle_Count 0x0032 087 087 000 Old_age Always - 27004
194 Temperature_Celsius 0x0022 034 054 000 Old_age Always - 34 (0 10 0 0 0)
195 Hardware_ECC_Recovered 0x001a 048 041 000 Old_age Always - 81234683
196 Reallocated_Event_Count 0x0033 091 091 036 Pre-fail Always - 201
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1846
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 3
SMART Error Log Version: 1
ATA Error Count: 27473 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 27473 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:18.260 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:15.784 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:13.274 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
Error 27472 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:15.784 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:13.274 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
Error 27471 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.288 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.225 READ DMA EXT
Error 27470 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.288 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.225 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.166 READ DMA EXT
Error 27469 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 01 00 00 00 e0 00 21:58:55.850 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.746 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.642 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.539 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.435 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 10198 547053969
# 2 Short offline Completed: read failure 90% 10197 547053969
# 3 Short offline Completed: read failure 90% 10197 547053969
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Я понятия не имею, что это означает, так как я не совсем знаком с Linux, поэтому в основном я спрашиваю: диск неисправен или его можно починить? Любая помощь приветствуется!