После установки Windows 8 (проблема не возникала в Windows 7), мой ноутбук зависает:

  • Все приложения постепенно перестают отвечать при взаимодействии с ним в течение минуты или около того, а затем все начинает работать снова.

Обычно проблема возникает вскоре после входа в систему.

Глядя на диспетчер задач, я вижу это во время блокировки:

диспетчер задач во время блокировки приложения

Активное время == 100%. Скорость передачи данных на диск == 0.

Диск SSD Crucial M4 CT256M4SSD2

Информация об аппаратных идентификаторах из диспетчера устройств:

IDE\DiskM4-CT256M4SSD2__________________________0001____
IDE\M4-CT256M4SSD2__________________________0001____
IDE\DiskM4-CT256M4SSD2__________________________
M4-CT256M4SSD2__________________________0001____
GenDisk

Вывод из DiskCheckup:

* DiskCheckup V3.1 Build: 1006 Report *

SysInfo DLL Version:            SysInfo v1.0 Build: 1030
Time of export:                 13:19:07 19-Apr-2013

Device information:             
   Device ID:                   0
   Interface:                   RAID
   Device Capacity:             244191 MB
   Serial Number:               0000000011180306C84D
   Model Number:                M4-CT256M4SSD2
   Firmware Revision:           0001
   Partitions:                  
      C:         244195 MB

ATA information:                

   Disk geometry:               
      Cylinders:                31130
      Tracks/Cylinder:          255
      Sectors/Track:            63
      Bytes/Sector:             512
      Total disk sectors:       500118192
      Logical sector size:      512
      Physical sector size:     512
      Media rotation rate:      SSD
      Buffer size:              0 KB
      ECC size:                 0 Bytes

   Standards compliance:          
      ATA8-ACS Supported:         Yes
      ATA/ATAPI-7 Supported:      Yes
      ATA/ATAPI-6 Supported:      Yes
      ATA/ATAPI-5 Supported:      Yes
      ATA/ATAPI-4 Supported:      Yes
      Serial/Parallel:            Serial
         SATA 3.0 Compilance:     Yes
         SATA 2.6 Compilance:     Yes
         SATA 2.5 Compilance:     Yes
         SATA II: Ext Compilance: Yes
         SATA 1.0a Compilance:    Yes
         ATA8-AST Compilance:     Yes
   World Wide ID:                 500A07510306C84D

   Feature support:                                          
      SMART supported:                                       Yes
         SMART enabled:                                      Yes
      SMART self-test supported:                             Yes
      SMART error log supported:                             Yes
      LBA supported:                                         Yes
      IORDY supported:                                       Yes
      CFast supported:                                       No
      DMA supported:                                         Yes
         Maximum Multiword DMA mode supported:               2
         Multiword DMA selected:                             None
         Maximum UltraDMA mode supported:                    5
         UltraDMA selected:                                  5
      Maximum PIO mode supported:                            4
      SATA Compliance:                                       Yes
         NCQ priority information supported:                 Yes
         Unload while NCQ commands are outstanding supported:No
         Phy Event Counters supported:                       Yes
         Receipt of power management requests supported:     Yes
         NCQ feature set supported:                          Yes
         SATA Gen2 Signaling Speed (3.0Gb/s) supported:      Yes
         SATA Gen1 Signaling Speed (1.5Gb/s) supported:      Yes
         Software Settings Preservation:                     Supported, Enabled
         In-order data delivery:                             Not supported
         Initiating power management:                        Supported, Enabled
         DMA Setup auto-activation:                          Supported, Enabled
         Non-zero buffer offsets:                            Not supported
      Trusted Computing supported:                           No
      Host Protected Area (HPA) supported:                   Yes
      Read look-ahead supported:                             Yes
         Read look-ahead enabled:                            Yes
      Write cache supported:                                 Yes
         Write cache enabled:                                Yes
      Power management supported:                            Yes
      Security mode supported:                               Yes
         Security mode enabled:                              No
      Device Configuration Overlay (DCO) supported:          Yes
      48bit Addressing supported:                            Yes
      Auto Acoustic Managment (AAM) supported:               No
      Power-up in Standby (PUIS) supported:                  No
      Advanced Power Management (APM) supported:             Yes
         Advanced Power Management (APM) enabled:            Yes
         Current APM level:                                  Maximum performance
      CompactFlash Association (CFA) supported:              No
      General Purpose Logging (GPL) supported:               Yes
      Streaming supported:                                   No
      Media card pass through supported:                     No
      Extended power conditions supported:                   No
      Extended status reporting supported:                   No
      Write-read-verify supported:                           Yes
         Write-read-verify enabled:                          No
      Free-fall control supported:                           No
      TRIM command supported:                                Yes
      SCT command transport supported:                       Yes
      NV Cache enabled:                                      No
      NV Cache Power Management supported:                   No

SMART ATTRIBUTES:
 ID Description                   Status Value Worst Threshold Raw Value     TEC
-------------------------------------------------------------------------------------
  1 Raw Read Error Rate           OK     100   100   50        90            N.A.  
  5 Reallocated Sector Count      OK     100   100   10        0             N.A.  
  9 Power On Time                 OK     100   100   1         5002          N.A.  
 12 Power Cycle Count             OK     100   100   1         645           N.A.  
170 (Unknown attribute)           OK     100   100   10        0             N.A.  
171 (Unknown attribute)           OK     100   100   1         32            N.A.  
172 (Unknown attribute)           OK     100   100   1         0             N.A.  
173 (Unknown attribute)           OK     94    94    10        199           N.A.  
174 (Unknown attribute)           OK     100   100   1         5             N.A.  
181 (Unknown attribute)           OK     100   100   1         8327986808032 N.A.  
183 SATA Downshift Error Count    OK     100   100   1         0             N.A.  
184 End-to-End error              OK     100   100   50        0             N.A.  
187 Reported Uncorrectable Errors OK     100   100   1         505           N.A.  
188 Command Timeout               OK     100   100   1         0             N.A.  
189 High Fly Writes               OK     100   100   1         124           N.A.  
195 Hardware ECC Recovered        OK     100   100   1         124415        N.A.  
196 Reallocation Event Count      OK     100   100   1         0             N.A.  
197 Current Pending Sector Count  OK     100   100   1         0             N.A.  
198 Uncorrectable Sector Count    OK     100   100   1         0             N.A.  
199 UltraDMA CRC Error Count      OK     100   100   1         0             N.A.  
202 Data Address Mark Errors      OK     94    94    1         6             N.A.  
206 Flying Height                 OK     100   100   1         32            N.A.  

1 ответ1

0

IDE\DiskM4

Похоже, вы запускаете жесткий диск в медленном старом режиме IDE. Вместо этого используйте AHCI. Установите последние версии драйверов AHCI, перейдите в BIOS/UEFI и измените режим SATA с IDE на AHCI.

Всё ещё ищете ответ? Посмотрите другие вопросы с метками .