Хорошо, так что короткая история: у меня была Windows 8. Работало нормально. При обновлении до Windows 10 процесс прервался, повредив мою установку Windows.
Я отформатировал и переустановил windows. хорошо.
Через месяц он больше не загружается. ХОРОШО.
Я снова форматирую, переустанавливаю Windows снова. Затем, когда Windows обновлялась сама, после определенного обновления она больше не загружалась. промыть и повторить, я форматирую, снова устанавливаю windows, он обновляется и больше не загружается.
Теперь я пытаюсь выяснить, в чем проблема. Это жесткий диск, другое оборудование или обновление?
сейчас я нахожусь на загрузочной флешке Ubuntu. Я попытался выяснить, не сломалось ли мое оборудование, и, поскольку Ubuntu работает очень хорошо, я предполагаю, что компьютер без жесткого диска может быть в порядке.
Используя smartctl, я получил следующий отчет, вставленный в pastbin:
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: 5VE0VSAH
LU WWN Device Id: 5 000c50 0139b26cc
Firmware Version: 0001SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat May 28 16:53:57 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 140) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 104 076 006 Pre-fail Always - 68954612
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3350
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 066 060 030 Pre-fail Always - 438506601361
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20514
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 037 020 Old_age Always - 3314
184 End-to-End_Error 0x0032 076 076 099 Old_age Always FAILING_NOW 24
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 10156
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 592
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 062 048 045 Old_age Always - 38 (Min/Max 27/38)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 469038
194 Temperature_Celsius 0x0022 038 052 000 Old_age Always - 38 (0 11 0 0 0)
195 Hardware_ECC_Recovered 0x001a 044 040 000 Old_age Always - 68954612
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 10726 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10726 occurred at disk power-on lifetime: 20513 hours (854 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d8 cc 06 00 Error: UNC at LBA = 0x0006ccd8 = 445656
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 d1 cc 06 e0 00 00:00:31.281 READ DMA EXT
25 00 08 87 b9 13 e0 00 00:00:31.280 READ DMA EXT
25 00 08 c9 cc 06 e0 00 00:00:31.280 READ DMA EXT
25 00 08 c1 cc 06 e0 00 00:00:31.279 READ DMA EXT
25 00 08 8f b9 13 e0 00 00:00:31.279 READ DMA EXT
Error 10725 occurred at disk power-on lifetime: 20513 hours (854 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d8 cc 06 00 Error: UNC at LBA = 0x0006ccd8 = 445656
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 99 cc 06 e0 00 00:00:28.805 READ DMA EXT
25 00 40 59 cc 06 e0 00 00:00:28.803 READ DMA EXT
25 00 40 19 cc 06 e0 00 00:00:28.801 READ DMA EXT
25 00 40 99 ca 06 e0 00 00:00:28.798 READ DMA EXT
25 00 40 59 ca 06 e0 00 00:00:28.787 READ DMA EXT
Error 10724 occurred at disk power-on lifetime: 20513 hours (854 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d8 cc 06 00 Error: UNC at LBA = 0x0006ccd8 = 445656
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 b9 c9 06 e0 00 00:00:26.276 READ DMA EXT
25 00 00 b9 c8 06 e0 00 00:00:26.262 READ DMA EXT
25 00 08 3f 74 62 e0 00 00:00:26.247 READ DMA EXT
25 00 08 57 a8 61 e0 00 00:00:26.241 READ DMA EXT
25 00 08 77 1c 61 e0 00 00:00:26.226 READ DMA EXT
Error 10723 occurred at disk power-on lifetime: 20513 hours (854 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d8 cc 06 00 Error: UNC at LBA = 0x0006ccd8 = 445656
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 99 cc 06 e0 00 00:11:40.047 READ DMA EXT
25 00 40 59 cc 06 e0 00 00:11:40.044 READ DMA EXT
25 00 40 19 cc 06 e0 00 00:11:40.044 READ DMA EXT
25 00 40 d9 cb 06 e0 00 00:11:40.043 READ DMA EXT
25 00 40 99 cb 06 e0 00 00:11:40.043 READ DMA EXT
Error 10722 occurred at disk power-on lifetime: 20513 hours (854 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d8 cc 06 00 Error: UNC at LBA = 0x0006ccd8 = 445656
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 b9 c9 06 e0 00 00:11:37.591 READ DMA EXT
25 00 00 b9 c8 06 e0 00 00:11:37.580 READ DMA EXT
25 00 08 8f 24 61 e0 00 00:11:37.578 READ DMA EXT
25 00 8d 19 6d 07 e0 00 00:11:37.565 READ DMA EXT
25 00 7a 8e 6c 07 e0 00 00:11:37.564 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 20514 445656
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Я не уверен, что все это значит, я полагаю, что это обычно выявляет некоторые ошибки, даже если все в основном нормально, поэтому я не могу понять, означает ли что-либо из этого серьезный ущерб или нет.
Я просто хочу знать, стоит ли мне просто перейти на SSD и установить на него Windows 10 или попробовать Windows 10 на моем текущем жестком диске.